Star64 with RISC-V cpu U-Boot SPL 2021.10 (Jan 19 2023 - 04:09:41 +0800) DDR version: dc2e84f0. Trying to boot from SPI OpenSBI v1.2 ____ _____ ____ _____ / __ \ / ____| _ \_ _| | | | |_ __ ___ _ __ | (___ | |_) || | | | | | '_ \ / _ \ '_ \ \___ \| _ < | | | |__| | |_) | __/ | | |____) | |_) || |_ \____/| .__/ \___|_| |_|_____/|____/_____| | | |_| Platform Name : StarFive VisionFive V2 Platform Features : medeleg Platform HART Count : 5 Platform IPI Device : aclint-mswi Platform Timer Device : aclint-mtimer @ 4000000Hz Platform Console Device : uart8250 Platform HSM Device : jh7110-hsm Platform PMU Device : --- Platform Reboot Device : pm-reset Platform Shutdown Device : pm-reset Firmware Base : 0x40000000 Firmware Size : 288 KB Runtime SBI Version : 1.0 Domain0 Name : root Domain0 Boot HART : 1 Domain0 HARTs : 0*,1*,2*,3*,4* Domain0 Region00 : 0x0000000002000000-0x000000000200ffff (I) Domain0 Region01 : 0x0000000040000000-0x000000004007ffff () Domain0 Region02 : 0x0000000000000000-0xffffffffffffffff (R,W,X) Domain0 Next Address : 0x0000000040200000 Domain0 Next Arg1 : 0x0000000042200000 Domain0 Next Mode : S-mode Domain0 SysReset : yes Boot HART ID : 1 Boot HART Domain : root Boot HART Priv Version : v1.11 Boot HART Base ISA : rv64imafdcbx Boot HART ISA Extensions : none Boot HART PMP Count : 8 Boot HART PMP Granularity : 4096 Boot HART PMP Address Bits: 34 Boot HART MHPM Count : 2 Boot HART MIDELEG : 0x0000000000000222 Boot HART MEDELEG : 0x000000000000b109 U-Boot 2021.10 (Jan 19 2023 - 04:09:41 +0800), Build: jenkins-github_visionfive2-6 CPU: rv64imacu Model: StarFive VisionFive V2 DRAM: 8 GiB MMC: sdio0@16010000: 0, sdio1@16020000: 1 Loading Environment from SPIFlash... SF: Detected gd25lq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment StarFive EEPROM format v2 --------EEPROM INFO-------- Vendor : PINE64 Product full SN: STAR64V1-2310-D008E000-00000XXX data version: 0x2 PCB revision: 0xc1 BOM revision: A Ethernet MAC0 address: 6c:cf:39:XX:XX:XX Ethernet MAC1 address: 6c:cf:39:XX:XX:XX In: serial@10000000 Out: serial@10000000 Err: serial@10000000 Model: StarFive VisionFive V2 Net: eth0: ethernet@16030000, eth1: ethernet@16040000 switch to partitions #0, OK mmc1 is current device found device 1 bootmode flash device 1 Failed to load 'uEnv.txt' Can't set block device Hit any key to stop autoboot: 0 1562 bytes read in 5 ms (304.7 KiB/s) Importing environment from mmc1 ... Can't set block device ## Warning: defaulting to text format switch to partitions #0, OK mmc1 is current device 15161340 bytes read in 641 ms (22.6 MiB/s) ## Loading kernel from FIT Image at a0000000 ... Using 'conf-starfive_jh7110-pine64-star64.dtb' configuration Trying 'kernel-1' kernel subimage Description: Linux kernel Type: Kernel Image Compression: gzip compressed Data Start: 0xa00000f0 Data Size: 9767777 Bytes = 9.3 MiB Architecture: RISC-V OS: Linux Load Address: 0x40200000 Entry Point: 0x40200000 Hash algo: sha256 Hash value: 6ff0b93eb70cc0074c0fd066fc2a4372a38db55176634d85a749b9a20e1cff83 Verifying Hash Integrity ... sha256+ OK ## Loading ramdisk from FIT Image at a0000000 ... Using 'conf-starfive_jh7110-pine64-star64.dtb' configuration Trying 'ramdisk-1' ramdisk subimage Description: star64-image-initramfs Type: RAMDisk Image Compression: uncompressed Data Start: 0xa095cb14 Data Size: 5343011 Bytes = 5.1 MiB Architecture: RISC-V OS: Linux Load Address: 0x46100000 Entry Point: unavailable Hash algo: sha256 Hash value: 15fe620edab644328b04e73539a4d035eb18337087479a6464c5f44cb295768f Verifying Hash Integrity ... sha256+ OK Loading ramdisk from 0xa095cb14 to 0x46100000 ## Loading fdt from FIT Image at a0000000 ... Using 'conf-starfive_jh7110-pine64-star64.dtb' configuration Trying 'fdt-starfive_jh7110-pine64-star64.dtb' fdt subimage Description: Flattened Device Tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0xa0950d78 Data Size: 48314 Bytes = 47.2 KiB Architecture: RISC-V Load Address: 0x46000000 Hash algo: sha256 Hash value: 4c332080330ea9f21f3263a5f6111f01511a3661f10af4b4d0ca65e4a10fd849 Verifying Hash Integrity ... sha256+ OK Loading fdt from 0xa0950d78 to 0x46000000 Booting using the fdt blob at 0x46000000 Uncompressing Kernel Image ## Error: "cpu_vol_set" not defined Booting kernel in ## Flattened Device Tree blob at 46000000 Booting using the fdt blob at 0x46000000 Using Device Tree in place at 0000000046000000, end 000000004600efff Starting kernel ... clk u5_dw_i2c_clk_core already disabled clk u5_dw_i2c_clk_apb already disabled [ 0.000000] Linux version 5.15.115 (oe-user@oe-host) (riscv64-pine64-linux-gcc (GCC) 11.3.0, GNU ld (GNU Binutils) 2.38.20220708) #1 SMP Sat Jun 10 09:56:27 UTC 2023 [ 0.000000] OF: fdt: Ignoring memory range 0x40000000 - 0x40200000 [ 0.000000] Machine model: Pine64 Star64 [ 0.000000] earlycon: sbi0 at I/O port 0x0 (options '') [ 0.000000] printk: bootconsole [sbi0] enabled [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000080000000, size 512 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000040200000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000023fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040200000-0x00000000c010ffff] [ 0.000000] node 0: [mem 0x00000000c0110000-0x00000000c01fffff] [ 0.000000] node 0: [mem 0x00000000c0200000-0x000000023fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040200000-0x000000023fffffff] [ 0.000000] SBI specification v1.0 detected [ 0.000000] SBI implementation ID=0x1 Version=0x10002 [ 0.000000] SBI TIME extension detected [ 0.000000] SBI IPI extension detected [ 0.000000] SBI RFENCE extension detected [ 0.000000] SBI SRST extension detected [ 0.000000] SBI v0.2 HSM extension detected [ 0.000000] CPU with hartid=0 is not available [ 0.000000] CPU with hartid=0 is not available [ 0.000000] riscv: base ISA extensions acdfim [ 0.000000] riscv: ELF capabilities acdfim [ 0.000000] percpu: Embedded 18 pages/cpu s34088 r8192 d31448 u73728 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 2067975 [ 0.000000] Kernel command line: earlyprintk console=tty1 console=ttyS0,115200 rootwait earlycon=sbi root=/dev/mmcblk1p4 [ 0.000000] Unknown kernel command line parameters "earlyprintk", will be passed to user space. [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x00000000fbfff000-0x00000000fffff000] (64MB) [ 0.000000] Memory: 7570656K/8386560K available (10959K kernel code, 7222K rwdata, 6144K rodata, 2185K init, 405K bss, 291616K reserved, 524288K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] rcu: RCU debug extended QS entry/exit. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] CPU with hartid=0 is not available [ 0.000000] riscv-intc: unable to find hart id for /cpus/cpu@0/interrupt-controller [ 0.000000] riscv-intc: 64 local interrupts mapped [ 0.000000] plic: plic@c000000: mapped 136 interrupts with 4 handlers for 9 contexts. [ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [1] [ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 881590404240 ns [ 0.000001] sched_clock: 64 bits at 4MHz, resolution 250ns, wraps every 2199023255500ns [ 0.008240] clocksource: timer@13050000.ch0: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.018439] clocksource: timer@13050000.ch1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.028753] clocksource: timer@13050000.ch2: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.039067] clocksource: timer@13050000.ch3: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.049644] Console: colour dummy device 80x25 [ 0.054525] printk: console [tty1] enabled [ 0.058576] Calibrating delay loop (skipped), value calculated using timer frequency.. 8.00 BogoMIPS (lpj=40000) [ 0.068778] pid_max: default: 32768 minimum: 301 [ 0.073773] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.081430] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.091157] ASID allocator disabled [ 0.094702] rcu: Hierarchical SRCU implementation. [ 0.100419] smp: Bringing up secondary CPUs ... [ 0.106835] smp: Brought up 1 node, 4 CPUs [ 0.112824] devtmpfs: initialized [ 0.124536] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.134320] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.154754] pinctrl core: initialized pinctrl subsystem [ 0.161295] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.167857] thermal_sys: Registered thermal governor 'step_wise' [ 0.168209] cpuidle: using governor menu [ 0.200503] platform soc:dsi-output: Fixing up cyclic dependency with 29400000.dc8200 [ 0.208795] platform 295d0000.mipi: Fixing up cyclic dependency with soc:dsi-output [ 0.216798] platform 29590000.hdmi: Fixing up cyclic dependency with 29400000.dc8200 [ 0.265612] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.272235] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.283002] vgaarb: loaded [ 0.285887] SCSI subsystem initialized [ 0.289785] usbcore: registered new interface driver usbfs [ 0.295225] usbcore: registered new interface driver hub [ 0.300601] usbcore: registered new device driver usb [ 0.305999] mc: Linux media interface: v0.10 [ 0.310215] videodev: Linux video capture interface: v2.00 [ 0.316003] Advanced Linux Sound Architecture Driver Initialized. [ 0.323006] clocksource: Switched to clocksource riscv_clocksource [ 0.337310] NET: Registered PF_INET protocol family [ 0.343319] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.358611] tcp_listen_portaddr_hash hash table entries: 4096 (order: 5, 163840 bytes, linear) [ 0.367380] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.375073] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.383777] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear) [ 0.393414] TCP: Hash tables configured (established 65536 bind 65536) [ 0.400150] UDP hash table entries: 4096 (order: 6, 393216 bytes, linear) [ 0.407256] UDP-Lite hash table entries: 4096 (order: 6, 393216 bytes, linear) [ 0.415126] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.421324] RPC: Registered named UNIX socket transport module. [ 0.427183] RPC: Registered udp transport module. [ 0.431924] RPC: Registered tcp transport module. [ 0.436711] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.443956] PCI: CLS 0 bytes, default 64 [ 0.448859] Initialise system trusted keyrings [ 0.453264] Unpacking initramfs... [ 0.457394] workingset: timestamp_bits=62 max_order=21 bucket_order=0 [ 0.471280] NFS: Registering the id_resolver key type [ 0.476337] Key type id_resolver registered [ 0.480504] Key type id_legacy registered [ 0.484708] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.491342] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 0.498881] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.503523] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.510043] fuse: init (API version 7.34) [ 0.553092] NET: Registered PF_ALG protocol family [ 0.557843] Key type asymmetric registered [ 0.561978] Asymmetric key parser 'x509' registered [ 0.567046] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 0.574405] io scheduler mq-deadline registered [ 0.578963] io scheduler kyber registered [ 0.683685] clk-starfive-jh7110 13020000.clock-controller: starfive JH7110 clkgen init successfully. [ 0.694042] L2CACHE: DataError @ 0x00000000.08040140 [ 0.699000] L2CACHE: DataFail @ 0x00000000.0804005B [ 0.703994] L2CACHE: No. of Banks in the cache: 8 [ 0.708645] L2CACHE: No. of ways per bank: 16 [ 0.713084] L2CACHE: Sets per bank: 256 [ 0.716963] L2CACHE: Bytes per cache block: 64 [ 0.721468] L2CACHE: Index of the largest way enabled: 15 [ 0.724961] Initramfs unpacking failed: invalid magic at start of compressed archive [ 0.727257] jh7110-pmu 17030000.power-controller: registered 8 power domains [ 0.755626] Freeing initrd memory: 14804K [ 0.819438] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled [ 0.829421] @@#########################@@ [ 0.840114] @@ dev ptr:ffffffe0bff3ac00/1500/1 [ 0.844761] PVR_K: 1: Read BVNC 36.50.54.182 from HW device registers [ 0.851262] PVR_K: 1: RGX Device registered BVNC 36.50.54.182 with 1 core in the system [ 0.860595] PVR_K: 1: RGX Firmware image 'rgx.fw.36.50.54.182' loaded [ 0.870649] PVR_K: 1: Shader binary image 'rgx.sh.36.50.54.182' loaded [ 0.879290] [drm] Initialized pvr 1.17.6210866 20170530 for 18000000.gpu on minor 0 [ 0.896420] loop: module loaded [ 0.901715] spi-nor spi0.0: gd25lq128d (16384 Kbytes) [ 0.913071] 3 fixed-partitions partitions found on MTD device 13010000.spi.0 [ 0.920048] Creating 3 MTD partitions on "13010000.spi.0": [ 0.925623] 0x000000000000-0x000000040000 : "spl" [ 0.932013] 0x000000100000-0x000000400000 : "uboot" [ 0.938468] 0x000000f00000-0x000001000000 : "data" [ 0.947115] CAN device driver interface [ 0.951840] starfive-eth-plat 16030000.ethernet: User ID: 0x41, Synopsys ID: 0x52 [ 0.959288] starfive-eth-plat 16030000.ethernet: DWMAC4/5 [ 0.964815] starfive-eth-plat 16030000.ethernet: DMA HW capability register supported [ 0.972684] starfive-eth-plat 16030000.ethernet: RX Checksum Offload Engine supported [ 0.980581] starfive-eth-plat 16030000.ethernet: Wake-Up On Lan supported [ 0.987505] starfive-eth-plat 16030000.ethernet: TSO supported [ 0.993320] starfive-eth-plat 16030000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 1.001719] starfive-eth-plat 16030000.ethernet: Enabled L3L4 Flow TC (entries=1) [ 1.009273] starfive-eth-plat 16030000.ethernet: Enabled RFS Flow TC (entries=8) [ 1.016728] starfive-eth-plat 16030000.ethernet: TSO feature enabled [ 1.023135] starfive-eth-plat 16030000.ethernet: Using 40 bits DMA width [ 1.268417] YT8531 Gigabit Ethernet stmmac-0:00: attached PHY driver (mii_bus:phy_addr=stmmac-0:00, irq=POLL) [ 1.278309] YT8531 Gigabit Ethernet stmmac-0:01: attached PHY driver (mii_bus:phy_addr=stmmac-0:01, irq=POLL) [ 1.290011] starfive-eth-plat 16040000.ethernet: User ID: 0x41, Synopsys ID: 0x52 [ 1.297451] starfive-eth-plat 16040000.ethernet: DWMAC4/5 [ 1.302964] starfive-eth-plat 16040000.ethernet: DMA HW capability register supported [ 1.310866] starfive-eth-plat 16040000.ethernet: RX Checksum Offload Engine supported [ 1.318755] starfive-eth-plat 16040000.ethernet: Wake-Up On Lan supported [ 1.325666] starfive-eth-plat 16040000.ethernet: TSO supported [ 1.331477] starfive-eth-plat 16040000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 1.339908] starfive-eth-plat 16040000.ethernet: Enabled L3L4 Flow TC (entries=1) [ 1.347443] starfive-eth-plat 16040000.ethernet: Enabled RFS Flow TC (entries=8) [ 1.354895] starfive-eth-plat 16040000.ethernet: TSO feature enabled [ 1.361290] starfive-eth-plat 16040000.ethernet: Using 40 bits DMA width [ 1.605303] YT8531 Gigabit Ethernet stmmac-1:00: attached PHY driver (mii_bus:phy_addr=stmmac-1:00, irq=POLL) [ 1.615183] YT8531 Gigabit Ethernet stmmac-1:01: attached PHY driver (mii_bus:phy_addr=stmmac-1:01, irq=POLL) [ 1.627112] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.633600] ehci-pci: EHCI PCI platform driver [ 1.638114] ehci-platform: EHCI generic platform driver [ 1.644073] usbcore: registered new interface driver cdc_acm [ 1.649655] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.657781] usbcore: registered new interface driver cdc_wdm [ 1.683484] starfive-rtc 17040000.rtc: registered as rtc0 [ 1.688960] i2c_dev: i2c /dev entries driver [ 1.693433] usbcore: registered new interface driver uvcvideo [ 1.713039] thermal thermal_zone0: failed to read out thermal zone (-110) [ 1.720076] starfive-wdt 13070000.wdog: Heartbeat: timeout=15, count/2=180000000 (0aba9500) [ 1.729700] sdhci: Secure Digital Host Controller Interface driver [ 1.735833] sdhci: Copyright(c) Pierre Ossman [ 1.740253] Synopsys Designware Multimedia Card Interface Driver [ 1.746638] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.752744] ledtrig-cpu: registered to indicate activity on CPUs [ 1.759178] jh7110-sec 16000000.crypto: Unable to request sec_m dma channel in DMA channel [ 1.767392] jh7110-sec 16000000.crypto: Cannot initial dma chan [ 1.773663] usbcore: registered new interface driver usbhid [ 1.779158] usbhid: USB HID core driver [ 1.783164] usbcore: registered new interface driver rtl8852bu [ 1.789178] riscv-pmu-sbi: SBI PMU extension is available [ 1.794527] riscv-pmu-sbi: 16 firmware and 4 hardware counters [ 1.800381] riscv-pmu-sbi: Perf sampling/filtering is not supported as sscof extension is not available [ 1.810215] usbcore: registered new interface driver snd-usb-audio [ 1.818519] NET: Registered PF_INET6 protocol family [ 1.824812] Segment Routing with IPv6 [ 1.828458] In-situ OAM (IOAM) with IPv6 [ 1.832466] NET: Registered PF_PACKET protocol family [ 1.837544] can: controller area network core [ 1.842003] NET: Registered PF_CAN protocol family [ 1.846796] can: raw protocol [ 1.849809] can: broadcast manager protocol [ 1.854080] can: netlink gateway - max_hops=1 [ 1.858958] 9pnet: Installing 9P2000 support [ 1.863259] Key type dns_resolver registered [ 1.868372] Loading compiled-in X.509 certificates [ 1.910512] starfive_jh7110-pinctrl 13040000.gpio: SiFive GPIO chip registered 64 GPIOs [ 1.919273] starfive_jh7110-pinctrl 17020000.gpio: SiFive GPIO chip registered 4 GPIOs [ 1.927366] pl08xdmac 16008000.sec_dma: initialized 8 virtual memcpy channels [ 1.934469] pl08xdmac 16008000.sec_dma: initialized 16 virtual slave channels [ 1.943615] debugfs: Directory '16008000.sec_dma' with parent 'dmaengine' already present! [ 1.951819] pl08xdmac 16008000.sec_dma: DMA: PL080 rev0 at 0x16008000 irq 23 [ 1.959190] ssp-pl022 10060000.spi: ARM PL022 driver for StarFive SoC platform, device ID: 0x00041022 [ 1.968377] ssp-pl022 10060000.spi: mapped registers from 0x0000000010060000 to (____ptrval____) [ 1.977648] ssp-pl022 10060000.spi: Requested frequency: 10000000 Hz is unsupported,select by default 8250000 Hz [ 1.988190] ssp-pl022 10060000.spi: will use autosuspend for runtime pm, delay 100ms [ 1.999799] rtc-hym8563 2-0051: no valid clock/calendar values available [ 2.006669] rtc-hym8563 2-0051: registered as rtc1 [ 2.012352] rtc-hym8563 2-0051: no valid clock/calendar values available [ 2.018995] rtc-hym8563 2-0051: hctosys: unable to read the hardware clock [ 2.028053] at24 5-0050: supply vcc not found, using dummy regulator [ 2.035204] at24 5-0050: 512 byte 24c04 EEPROM, writable, 16 bytes/write [ 2.044403] axp15060-regulator 5-0036: Register mipi_0p9 done! vol range:900 ~ 900 mV [ 2.054095] axp15060-regulator 5-0036: Register hdmi_1p8 done! vol range:1800 ~ 1800 mV [ 2.063953] axp15060-regulator 5-0036: Register sdio_vdd done! vol range:1800 ~ 1800 mV [ 2.073812] axp15060-regulator 5-0036: Register hdmi_0p9 done! vol range:900 ~ 900 mV [ 2.083507] axp15060-regulator 5-0036: Register vcc_3v3 done! vol range:3300 ~ 3300 mV [ 2.093760] axp15060-regulator 5-0036: Register cpu_vdd done! vol range:500 ~ 1540 mV [ 2.104627] pcie_plda 2c000000.pcie: Failed to get power-gpio, but maybe it's always on. [ 2.112814] pcie_plda 2c000000.pcie: host bridge /soc/pcie@2C000000 ranges: [ 2.119771] pcie_plda 2c000000.pcie: MEM 0x0038000000..0x003fffffff -> 0x0038000000 [ 2.127892] pcie_plda 2c000000.pcie: MEM 0x0980000000..0x09bfffffff -> 0x0980000000 [ 2.136062] ATR entry: 0x09c0000000 -> 0x0000000000 [0x0010000000] (param: 0x000001) [ 2.143823] ATR entry: 0x0038000000 -> 0x0038000000 [0x0008000000] (param: 0x000000) [ 2.151603] ATR entry: 0x0980000000 -> 0x0980000000 [0x0040000000] (param: 0x000000) [ 2.573274] pcie_plda 2c000000.pcie: Port link down, exit. [ 2.592441] clk-starfive-jh7110-vout 295c0000.clock-controller: starfive JH7110 clk_vout init successfully. [ 2.613887] clk-starfive-jh7110-isp 19810000.clock-controller: starfive JH7110 clk_isp init successfully. [ 2.624107] dw_axi_dmac_platform 16050000.dma-controller: DesignWare AXI DMA Controller, 4 channels [ 2.667489] printk: console [ttyS0] enabled0x10000000 (irq = 17, base_baud = 1500000) is a 16550A [ 2.667489] printk: console [ttyS0] enabled [ 2.675783] printk: bootconsole [sbi0] disabled [ 2.675783] printk: bootconsole [sbi0] disabled [ 2.686924] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 2.692448] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1 [ 2.700452] xhci-hcd xhci-hcd.1.auto: hcc params 0x200073c8 hci version 0x100 quirks 0x0000002000018010 [ 2.709915] xhci-hcd xhci-hcd.1.auto: irq 53, io mem 0x10110000 [ 2.716101] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 2.721610] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2 [ 2.729305] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 2.736678] hub 1-0:1.0: USB hub found [ 2.740478] hub 1-0:1.0: 1 port detected [ 2.744947] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.753783] hub 2-0:1.0: USB hub found [ 2.757580] hub 2-0:1.0: 1 port detected [ 2.762109] cdns3-starfive 10210000.usbdrd: usb mode 1 3.0 probe success [ 2.769057] jh7110-vin 19800000.vin_sysctl: stfcamss probe enter! [ 2.778700] jh7110-vin 19800000.vin_sysctl: stfcamss probe success! [ 2.796309] jh7110-sec 16000000.crypto: will run requests pump with realtime priority [ 2.796463] dwmmc_starfive 16020000.sdio1: IDMAC supports 32-bit address mode. [ 2.796464] dwmmc_starfive 16010000.sdio0: IDMAC supports 32-bit address mode. [ 2.796492] dwmmc_starfive 16010000.sdio0: Using internal DMA controller. [ 2.796499] dwmmc_starfive 16010000.sdio0: Version ID is 290a [ 2.796526] dwmmc_starfive 16010000.sdio0: DW MMC controller at irq 29,32 bit host data width,32 deep fifo [ 2.805186] mmc_host mmc0: card is non-removable. [ 2.811382] dwmmc_starfive 16020000.sdio1: Using internal DMA controller. [ 2.815458] jh7110-sec 16000000.crypto: Initialized [ 2.816622] starfive-i2s 120b0000.i2stx_4ch0: designware: play supported [ 2.816633] starfive-i2s 120b0000.i2stx_4ch0: designware: i2s master mode supported [ 2.817190] sf-mipi-dphy-tx 295e0000.mipi-dphy: sf_dphy_probe begin [ 2.817201] sf-mipi-dphy-tx 295e0000.mipi-dphy: ===> sf_dphy_probe enter, 445 [ 2.817350] sf-mipi-dphy-tx 295e0000.mipi-dphy: control ECO [ 2.817373] sf-mipi-dphy-tx 295e0000.mipi-dphy: supply mipi_1p8 not found, using dummy regulator [ 2.817689] sf-mipi-dphy-tx 295e0000.mipi-dphy: sf_dphy_probe end [ 2.817893] cdns-dsi 295d0000.mipi: dsi_sys_clk = 297000000 [ 2.818147] cdns-dsi 295d0000.mipi: starfive dsi bind end [ 2.821189] of_cfs_init [ 2.825445] dwmmc_starfive 16020000.sdio1: Version ID is 290a [ 2.831280] of_cfs_init: OK [ 2.840907] dwmmc_starfive 16020000.sdio1: DW MMC controller at irq 30,32 bit host data width,32 deep fifo [ 2.846226] starfive-pwmdac 100b0000.pwmdac: clk_apb0 = 49500000, clk_pwmdac_apb = 49500000, clk_pwmdac_core = 4068493 [ 2.852624] mmc_host mmc1: card is polling. [ 2.857904] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 3.033035] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 3.033036] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 400000Hz, actual 399193HZ div = 248) [ 3.064658] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 3.071333] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 3.079990] cfg80211: failed to load regulatory.db [ 3.093020] mmc_host mmc1: Bus speed (slot 0) = 198000000Hz (slot req 400000Hz, actual 399193HZ div = 248) [ 3.235049] hub 1-1:1.0: USB hub found [ 3.238935] hub 1-1:1.0: 4 ports detected [ 3.322002] starfive soc:display-subsystem: bound 29400000.dc8200 (ops 0xffffffff81078878) [ 3.330424] innohdmi-starfive 29590000.hdmi: inno hdmi bind begin [ 3.339467] innohdmi-starfive 29590000.hdmi: [drm:inno_hdmi_bind] registered Inno HDMI I2C bus driver success [ 3.350190] innohdmi-starfive 29590000.hdmi: HDMI&AUDIO register done. [ 3.356953] innohdmi-starfive 29590000.hdmi: inno hdmi bind end [ 3.362976] starfive soc:display-subsystem: bound 29590000.hdmi (ops 0xffffffff81079610) [ 3.371259] vs-simple-encoder soc:dsi-output: encoder_bind begin [ 3.377474] no panel, -517 [ 3.380271] vs-simple-encoder soc:dsi-output: encoder_bind error [ 3.386388] starfive soc:display-subsystem: bound soc:dsi-output (ops 0xffffffff81079258) [ 3.396491] [drm] Initialized starfive 1.0.0 20191101 for soc:display-subsystem on minor 1 [ 3.408490] mmc_host mmc1: Bus speed (slot 0) = 198000000Hz (slot req 50000000Hz, actual 49500000HZ div = 2) [ 3.418538] mmc1: new high speed SDHC card at address 0001 [ 3.425963] mmcblk1: mmc1:0001 SD16G 14.9 GiB [ 3.483103] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 300000Hz, actual 300000HZ div = 330) [ 3.683103] usb 1-1.1: new high-speed USB device number 3 using xhci-hcd [ 3.905781] starfive soc:display-subsystem: [drm] Cannot find any crtc or sizes [ 3.915366] hub 1-1.1:1.0: USB hub found [ 3.919488] hub 1-1.1:1.0: 4 ports detected [ 4.133042] usb 1-1.2: new high-speed USB device number 4 using xhci-hcd [ 4.415027] starfive soc:display-subsystem: [drm] Cannot find any crtc or sizes [ 4.927497] starfive soc:display-subsystem: [drm] Cannot find any crtc or sizes [ 4.938254] eric-tx CALL alloc_txring !!!! [ 4.940939] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 4.949776] GPT:3781225 != 31223807 [ 4.953281] GPT:Alternate GPT header not at the end of the disk. [ 4.959282] GPT:3781225 != 31223807 [ 4.962768] GPT: Use GNU Parted to correct GPT errors. [ 4.967939] mmcblk1: p1 p2 p3 p4 [ 5.153182] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 200000Hz, actual 200000HZ div = 495) [ 5.603128] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 100000Hz, actual 100000HZ div = 990) [ 6.003068] ALSA device list: [ 6.006070] #0: Starfive-PWMDAC-Sound-Card [ 6.010367] #1: Starfive-HDMI-Sound-Card [ 6.019527] Freeing unused kernel image (initmem) memory: 2184K [ 6.025815] Run /init as init process [ 6.179217] EXT4-fs (mmcblk1p4): mounted filesystem with ordered data mode. Opts: (null). Quota mode: disabled. [ 6.638036] systemd[1]: System time before build time, advancing clock. [ 6.722248] systemd[1]: systemd 250.5+ running in system mode (+PAM -AUDIT -SELINUX -APPARMOR +IMA -SMACK +SECCOMP -GCRYPT -GNUTLS -OPENSSL +ACL +BLKID -CURL -ELFUTILS -FIDO2 -IDN2 -IDN -IPTC +KMOD -LIBCRYPTSETUP +LIBFDISK -PCRE2 -PWQUALITY -P11KIT -QRENCODE -BZIP2 -LZ4 -XZ -ZLIB +ZSTD -BPF_FRAMEWORK +XKBCOMMON +UTMP +SYSVINIT default-hierarchy=hybrid) [ 6.753915] systemd[1]: Detected architecture riscv64. Welcome to PinIx 1.3 (pinix)! [ 6.804945] systemd[1]: Hostname set to . [ 6.826347] systemd[1]: Initializing machine ID from random generator. [ 6.932610] systemd-sysv-generator[280]: SysV service '/etc/init.d/rc.pvr' lacks a native systemd unit file. Automatically generating a unit file for compatibility. Please update package to include a native systemd unit file, in order to make it more safe and robust. [ 7.488621] systemd[1]: Queued start job for default target Multi-User System. [ 7.508535] systemd[1]: Created slice Slice /system/getty. [ OK ] Created slice Slice /system/getty. [ 7.545823] systemd[1]: Created slice Slice /system/modprobe. [ OK ] Created slice Slice /system/modprobe. [ 7.584376] systemd[1]: Created slice Slice /system/serial-getty. [ OK ] Created slice Slice /system/serial-getty. [ 7.624621] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 7.663893] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 7.703365] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 7.744379] systemd[1]: Reached target Host and Network Name Lookups. [ OK ] Reached target Host and Network Name Lookups. [ 7.783378] systemd[1]: Reached target Path Units. [ OK ] Reached target Path Units. [ 7.813240] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 7.853450] systemd[1]: Reached target Slice Units. [ OK ] Reached target Slice Units. [ 7.893248] systemd[1]: Reached target Swaps. [ OK ] Reached target Swaps. [ 7.949850] systemd[1]: Listening on RPCbind Server Activation Socket. [ OK ] Listening on RPCbind Server Activation Socket. [ 7.993582] systemd[1]: Reached target RPC Port Mapper. [ OK ] Reached target RPC Port Mapper. [ 8.034414] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 8.092978] systemd[1]: Listening on Process Core Dump Socket. [ OK ] Listening on Process Core Dump Socket. [ 8.133825] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 8.179963] systemd[1]: Journal Audit Socket was skipped because of a failed condition check (ConditionSecurity=audit). [ 8.191603] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 8.234354] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 8.274813] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 8.313584] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 8.354241] systemd[1]: Listening on User Database Manager Socket. [ OK ] Listening on User Database Manager Socket. [ 8.399611] systemd[1]: Mounting Huge Pages File System... Mounting Huge Pages File System... [ 8.436075] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... [ 8.475919] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 8.514090] systemd[1]: Kernel Trace File System was skipped because of a failed condition check (ConditionPathExists=/sys/kernel/tracing). [ 8.531076] systemd[1]: Mounting Temporary Directory /tmp... Mounting Temporary Directory /tmp... [ 8.567087] systemd[1]: Starting Create List of Static Device Nodes... Starting Create List of Static Device Nodes... [ 8.608126] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 8.649476] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 8.686828] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 8.738670] systemd[1]: Starting Start psplash boot splash screen... Starting Start psplash boot splash screen... [ 8.777850] systemd[1]: Starting RPC Bind... Starting RPC Bind... [ 8.813519] systemd[1]: File System Check on Root Device was skipped because of a failed condition check (ConditionPathIsReadWrite=!/). [ 8.834328] systemd[1]: Starting Journal Service... Starting Journal Service... [ 8.885954] systemd[1]: Load Kernel Modules was skipped because all trigger condition checks failed. [ 8.896775] systemd[1]: Mounting NFSD configuration filesystem... Mounting NFSD configuration filesystem... [ 8.935472] systemd[1]: Starting Generate network units from Kernel command line... Starting Generate network …ts from Kernel command line... [ 8.975312] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems EXT4-fs (mmcblk1p4): re-mounted. Opts: (null). Quota mode: disabled. [0m... [ 9.025221] systemd[1]: Starting Apply Kernel Variables... Starting Apply Kernel Variables... [ 9.056103] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 9.065442] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 9.120512] systemd[1]: Started RPC Bind. [ OK ] Started RPC Bind. [ 9.153479] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Kernel Debug File System. [ OK ] Mounted Temporary Directory /tmp. [ OK ] Finished Create List of Static Device Nodes. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [FAILED] Failed to start Start psplash boot splash screen. See 'systemctl status psplash-start.service' for details. [DEPEND] Dependency failed for Star…progress communication helper. [ OK ] Mounted NFSD configuration filesystem. [ OK ] Finished Generate network units from Kernel command line. [ OK ] Finished Remount Root and Kernel File Systems. [ OK ] Finished Apply Kernel Variables. Mounting FUSE Control File System... Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... [ 9.789857] systemd-journald[296]: Received client request to flush runtime journal. Starting Create System Users... [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Finished Coldplug All udev Devices. [ OK ] Reached target Preparation for Local File Systems. Mounting /var/volatile... Starting Rule-based Manage…for Device Events and Files... [ OK ] Mounted /var/volatile. Starting Load/Save Random Seed... [ OK ] Started Rule-based Manager for Device Events and Files. [ 10.493351] vdec: loading out-of-tree module taints kernel. [ 10.496101] venc: loading out-of-tree module taints kernel. [ 10.497788] jpu: loading out-of-tree module taints kernel. [ 10.498894] cnm_jpu 13090000.jpu: init device. [ 10.501977] vdec 130a0000.vpu_dec: device init. [ 10.511165] SUCCESS alloc_chrdev_region [ 10.514536] SUCCESS alloc_chrdev_region [ 10.538484] mailbox 13060000.mailbox: Mailbox enabled [ 10.731715] mailbox_test soc:mailbox_client@0: invalid resource [ 10.737723] mailbox_test soc:mailbox_client@0: invalid resource [ 10.743770] mailbox_test soc:mailbox_client@0: Successfully registered [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Load/Save RF Kill Switch Status... [ OK ] Started Load/Save RF Kill Switch Status. [ OK ] Found device /dev/disk/by-label/boot. [ 11.410871] Bluetooth: Core ver 2.22 [ 11.414547] NET: Registered PF_BLUETOOTH protocol family [ 11.419859] Bluetooth: HCI device and connection manager initialized [ 11.426297] Bluetooth: HCI socket layer initialized [ 11.431180] Bluetooth: L2CAP socket layer initialized [ 11.436299] Bluetooth: SCO socket layer initialized [ 11.469421] usbcore: registered new interface driver btusb [ 11.476478] Bluetooth: hci0: RTL: examining hci_ver=0b hci_rev=000b lmp_ver=0b lmp_subver=8852 [ 11.488841] Bluetooth: hci0: RTL: rom_version status=0 version=1 [ 11.494879] Bluetooth: hci0: RTL: loading rtl_bt/rtl8852bu_fw.bin [ 11.506134] Bluetooth: hci0: RTL: loading rtl_bt/rtl8852bu_config.bin [ 11.513545] Bluetooth: hci0: RTL: cfg_sz 6, total sz 38955 [ 11.746451] Bluetooth: hci0: RTL: fw version 0xdfb791cb Mounting /boot... Starting Start psplash boot splash screen... [FAILED] Failed to start Start psplash boot splash screen. See 'systemctl status psplash-start.service' for details. [DEPEND] Dependency failed for Star…progress communication helper. [ OK ] Mounted /boot. [ 12.213016] random: crng init done [ OK ] Reached target Local File Systems. Starting Rebuild Dynamic Linker Cache... Starting Create Volatile Files and Directories... [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Create Volatile Files and Directories. Starting Run pending postinsts... Starting Rebuild Journal Catalog... Starting Network Time Synchronization... Starting Record System Boot/Shutdown in UTMP... [ OK ] Finished Record System Boot/Shutdown in UTMP. [ OK ] Finished Rebuild Journal Catalog. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Set. [ OK ] Finished Rebuild Dynamic Linker Cache. Starting Update is Completed... [ OK ] Finished Update is Completed. [ OK ] Finished Run pending postinsts. [ OK ] Reached target System Initialization. [ OK ] Started Daily rotation of log files. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timer Units. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. Starting sshd.socket... [ OK ] Listening on sshd.socket. [ OK ] Reached target Socket Units. [ OK ] Reached target Basic System. Starting Save/Restore Sound Card State... [ OK ] Started Job spooling tools. Starting Avahi mDNS/DNS-SD Stack... Starting Bluetooth service... [ OK ] Started Periodic Command Scheduler. Starting D-Bus System Message Bus... Starting Network Time Service (one-shot ntpdate mode)... [ OK ] Started System Logging Service. Starting User Login Management... Starting OpenSSH Key Generation... [ OK ] Started D-Bus System Message Bus. [ OK ] Finished Save/Restore Sound Card State. [ OK ] Finished Network Time Service (one-shot ntpdate mode). [ OK ] Reached target Sound Card. Starting firewalld - dynamic firewall daemon... [ OK ] Started Bluetooth service. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Started User Login Management. [ OK ] Reached target Bluetooth Support. Starting Hostname Service... [ OK ] Started Hostname Service. [ OK ] Started firewalld - dynamic firewall daemon. [ OK ] Reached target Preparation for Network. Starting Network Manager... [ OK ] Started Network Manager. [ OK ] Reached target Network. Starting DNS forwarder and DHCP server... [ OK ] Started NFS status monitor for NFSv2/3 locking.. [ OK ] Started Respond to IPv6 Node Information Queries. [ OK ] Started Network Router Discovery Daemon. Starting Permit User Sessions... [ OK ] Finished star64 login: